document number: 37007 revision 24-nov-00 www.vishay.com 2 APD-128G032A vishay dale plasma display modules 128 x 32 graphics display with drive electronics ttl level data interface and integrated dc converter features ttl level video interface large characters highly visible for long distance viewing slim profile > 30:1 contrast ratio on board dc/dc converter bright and pleasant neon orange color very affordable optical specifications viewing area: 12.75" [323.8mm] w x 3.15" [80.01mm] l. character array: (8 x 8) 16 x 4. (6 x 8) 21 x 4. character size: 0.65" [16.51mm] h x 0.45" [11.43mm] w. pixel size: 0.050" [1.27mm]. pixel pitch: 0.100" [2.54mm]. luminance: 50 foot lamberts. electrical specifications voltage(s) required: vdc: + 12 to + 24 vdc. v cc : + 5 vdc. power required: typical = 12 watts. maximum = 45 watts. the APD-128G032A dc plasma display offers viewing qualities designers seek such as high contrast, viewing angle of 150 minimum and long distance readability. its bright (50 foot lambert minimum) with characters and graphics figures presented in a pleasing neon orange color against a black background. plasma is much more readable and eye-pleasing than liquid crystal or vacuum fluorescent displays and is filterable to red, amber or neutral density. these plasma display panels are driven in a standard row-column refresh method much like a crt display. the designer need only supply ttl level signals for serial data, dot clock, column latch, row data, row clock and display enable. the serial data is entered with the dot clock up to frequencies as high as 8mhz. after a row of 128 pixels is clocked in, the column latch signal is toggled and the data is latched. at the time the data is latched, the display is briefly disabled using the display enable signal, then the row pointer is advanced with the row clock signal. once each frame the row data must be asserted to synchronize the column serial data with the beginning row. the recommended scanning frequency is approximately 70hz, but may be as high as 200hz. the high clock rate on the data clock allows for rapid refresh and maximum access time to the refresh ram. ordering information description part number display module with drivers, ttl interface and on board dc converter .......................................................... ............... APD-128G032A power connector ................................................................................................................ ........................................................ 280108-13 data connector ................................................................................................................. .......................................................... 280105-05 standard electrical specifications* *recommended operating voltages. all maximums are absolute maximum. description symbol min. typ. max. units dc converter input vdc + 10.0 + 24.0 + 28.0 vdc dc converter power amps screen clear 50% lit 100% lit @ + 12 v 0.100 1.7 3.5 logic 1 input vih 2.0 vdc logic 0 input vil 0.8 vdc
www.vishay.com 3 APD-128G032A vishay dale document number: 37007 revision 24-nov-00 p3 - power connector pin description pin signal description 1 vdc + 12 v dc converter supply 2 gnd 3 gnd 4 key/n/c used to key connector p2 - data connector amp #103309-2 or equivalent. mates with amp 746195-2, molex 39-27-1146 or equivalent. pin description pin description 1 display enable 2 ground 3 row data 4 ground 5 row clock 6 ground 7 column latch 8 ground 9 dot clock 10 ground 11 serial data 12 ground 13 no connect 14 ground dimensions in inches [millimeters] 7.4 [187.96] 14.5 [368.3] mounting holes 0.150 [3.81] dia. 6 places 2.463 [62.56] 7.25 [184.15] 0.150 [3.81] 14.80 [375.92] 13.775 [349.88] 1.025 [26.04] 0.888 [22.56] 0.487 [12.37] 3.15 [80.01] 4.075 [103.50] 4.625 [117.48] 4.925 [125.10] 0.150 [3.81] 12.75 [323.85] pin #1 of p2 0.395 [10.03] 0.062 [1.58] pcb thickness pin #1 of p3
|
